Dump Trailer Capacity Calculator
A dump trailer has two capacities, and they run out at different times: the volume of the bed, and the weight the trailer is rated to carry. This calculator works out both: enter the bed length, width, and wall height in feet and it returns the volume in cubic feet and cubic yards, then, if you add a material density, the weight of a level load. Add the GVWR and the empty trailer weight as well and it works out the payload, converts it into the volume your material can legally take up, and tells you which of the two limits runs out first.
It is pre-filled with the common 7 by 14 trailer wearing 2 foot walls and a gravel density of 100 pounds per cubic foot. The bed holds 196 cubic feet, but the gravel in it would weigh 19,600 pounds, and that gap between the two numbers is the whole point of the page.
Scope, stated plainly: this calculator works from bed dimensions and material density, and if you also enter the GVWR and the empty trailer weight it checks the load against your trailer’s payload rating and tells you which limit runs out first, volume or weight. It has no per-axle inputs, so checking each axle against its own rating stays with you. The payload check is the one that decides whether a full bed is legal to haul.
Quick Answer
Key takeaways
- Bed volume is length x width x height in feet, divided by 27 for cubic yards. That is struck capacity, a load level with the top of the walls.
- Load weight is volume times material density. Gravel at about 100 lb per cubic foot and mulch at about 20 differ fivefold, so the same full bed can be a legal load or a serious overload depending on what is in it.
- Add the GVWR and the empty trailer weight and the calculator does the payload check itself: payload is GVWR minus empty weight, the payload becomes a weight-limited volume for your material, and the badge names whether volume or weight runs out first. Leave either field blank and you get volume and load weight only.
- Measure the inside of your own bed. Nominal widths overstate many real beds by 2 to 4 inches, and on a 7 by 14 that error is worth roughly 470 to 930 lb of gravel.
- Quick Answer
- How to measure the bed and run the numbers
- The formulas behind the result
- Worked example: a 7 by 14 trailer and a level load of gravel
- Material densities: what a yard of common loads weighs
- Two ways to decide a load is full
- What competing calculators miss
- Frequently Asked Questions
- Add This Calculator to Your Website
- References
How to measure the bed and run the numbers
Five minutes with a tape measure, then four entries, plus two optional ones for the payload check.
1. Measure the inside length and width. Run the tape along the bed floor between the walls. Manufacturers rate and sell by nominal size, but the load sits in the real opening, and trailer maker Kaufman Trailers notes in its dump trailer cubic yardage guide that its 7 ft wide models actually measure about 80 to 82 inches inside, not 84.
2. Measure the wall height. Floor to the top of the sidewall, including sideboards if you haul with them fitted. Height is the cheapest capacity there is: the same 7 by 14 bed is 7.26 cubic yards with 2 foot walls and 14.52 cubic yards with 4 foot walls.
3. Pick a density. Use the density table below, or your supplier’s figure. If the supplier quotes pounds per cubic yard, divide by 27 to get the pounds per cubic foot this calculator wants. If you are estimating how much material a job needs in the first place, the dirt calculator covers the project side of that question for soil and fill.
4. Read yards first, weight second. Yards tell you what to order and how many trips a job takes. The weight figure tells you whether one trip is allowed to carry it, which is the next check.
5. Add the GVWR and empty weight for the payload check (optional). Copy the GVWR from the data plate and the empty weight from a scale ticket, or the maker figure for your model as a starting point. The results then add a payload line and a weight-limited capacity line, and the badge states the verdict plainly: weight-limited, with the safe capacity in yards, or volume-limited, meaning a full bed stays within payload. Leave either field blank and nothing changes: you get the volume and load weight exactly as before.
The formulas behind the result
Every number the calculator returns comes from three multiplications and, when you enter the rating figures, one subtraction and one division. Nothing else is estimated or padded.
Bed volume (cubic yards) = Cubic feet / 27, because one cubic yard is 3 x 3 x 3 = 27 cubic feet, the conversion tabulated by the National Institute of Standards and Technology in its SP 811 guide to SI units.
Load weight (lb) = Cubic feet x Material density (lb per cubic foot), only when a density is entered.
Payload (lb) = GVWR (lb) – Empty trailer weight (lb), only when both are entered.
Weight-limited capacity = Payload / Material density, in cubic feet, divided by 27 for cubic yards, only when a density is entered. The safe capacity is whichever is smaller: the bed volume or the weight-limited capacity.
The same length x width x height step prices out any rectangular space, which is why the general cubic footage calculator is the right tool for boxes and rooms and this one is specific to trailer beds, yards, and load weight. Two terms matter for reading any capacity figure, here or on a sales brochure. Struck capacity is the volume with the load level with the top of the walls, and it is what this calculator computes. Heaped capacity adds a mound above the walls; it is always larger, always approximate, because it depends on how the material piles, and it should never be the number you check a payload against.
Worked example: a 7 by 14 trailer and a level load of gravel
The calculator is pre-filled with this case, so every figure below reproduces on Calculate.
| Input or result | Value |
|---|---|
| Bed length x width x height | 14 ft x 7 ft x 2 ft |
| Bed volume | 196.00 cubic feet |
| Bed volume in yards | 7.26 cubic yards |
| Material density (gravel) | 100 lb per cubic foot |
| Weight of a level full bed | 19,600.00 lb |
| GVWR (data plate) | 14,000 lb |
| Empty trailer weight (scale ticket) | 4,300 lb |
| Payload (GVWR minus empty weight) | 9,700.00 lb |
| Weight-limited gravel capacity | 3.59 cubic yards (97.00 cubic feet) |
Now the payload check, which the calculator does for you once the two rating figures are in. Take a common rating for this size of trailer: 14,000 lb GVWR on the data plate. A steel 7 by 14 dump trailer commonly weighs around 4,300 lb empty on a scale ticket. Enter 14000 in the GVWR field and 4300 in the empty trailer weight field and the results add the payload line: 14,000 minus 4,300 = 9,700 lb. They also add the weight-limited capacity line: gravel at 100 lb per cubic foot reaches 9,700 lb at 97 cubic feet, which is 3.59 cubic yards, roughly half the bed, and the badge reads weight-limited, with 3.59 cubic yards as the safe capacity. Fill the bed level anyway and the load alone is 19,600 lb, nearly double the payload, before the trailer’s own weight is even added. Your trailer’s figures will differ, so enter your plate GVWR and your scale weight instead; the method does not change.
Run the same bed and the same rating figures with lighter material and the limit flips. Mulch at 20 lb per cubic foot gives a level bed of 196 x 20 = 3,920 lb, far under the 9,700 lb payload, and the weight-limited capacity works out to 9,700 / 20 = 485 cubic feet, or 17.96 cubic yards, far more than the bed can hold. The badge reads volume-limited: with mulch the walls are the limit and you can fill the bed. Material choice, not trailer size, decides which limit you hit.
Material densities: what a yard of common loads weighs
Density is the input people guess worst, so use a table instead of a guess. These are typical dry-to-average figures; moisture is the big mover, and wet material can run 10 to 20 percent heavier than the same material dry.
| Material | lb per cubic foot | lb per cubic yard | Band |
|---|---|---|---|
| Mulch | 20 | 540 | Light |
| Topsoil, dry | 75 | 2,025 | Medium |
| Sand, dry | 90 | 2,430 | Dense |
| Gravel | 100 | 2,700 | Dense |
| Sand, wet | 115 | 3,105 | Dense |
The bands drive the badge in the calculator when no rating figures are entered: under 40 lb per cubic foot is light, 40 to 89 is medium, and 90 and up is dense, where a full bed will outrun most payload ratings. Enter the GVWR and empty weight and the badge changes job: it names the limit that runs out first for your trailer and material, weight-limited or volume-limited. Two neighbouring jobs show why the table matters more than the trailer. Hot asphalt mix is ordered and checked by volume with the asphalt volume calculator before it ever reaches a trailer, and concrete work is estimated the same way with the concrete volume calculator; in both trades the yard is the buying unit and the pound is the hauling limit, exactly the split this page is built around.
Two ways to decide a load is full
Every loading decision is one of these two rules. Knowing which one governs your material is most of safe hauling.
Load by volume: fill the bed
- Right for light material: mulch, brush, demolition debris, leaves.
- Simple to judge by eye at the loader.
- Risk: none from weight, but heaped light loads shed debris and need a tarp.
Load by weight: stop at payload
- Required for dense material: gravel, sand, soil, stone, rubble.
- Means loading part of the bed, often half or less, and counting loader buckets.
- Risk if ignored: overloaded axles and brakes, a dump body that strains to lift, and overweight citations.
Once the load is legal, the business question is what the trip costs to run. The dump truck operating cost calculator covers that side for truck work, fuel, maintenance, and cost per mile, and the same thinking applies to a trailer behind your own truck: fewer legal loads beat more overloaded ones on every cost that matters.
What competing calculators miss
The dump trailer tools ranking for this term run the same volume math, and at least one is a near twin of this tool, same inputs, same outputs. The misses are in what happens around the number.
Miss 1: a weight figure presented as permission. Competing pages label the volume-times-density result a maximum load weight and stop there, with no mention of GVWR or payload anywhere near it. A full-bed weight is not a rating; it is a number to compare against a rating. This calculator makes the comparison itself when you enter the GVWR and empty weight, and the worked example and FAQs spell out the same check, because the comparison is the safety-critical step.
Miss 2: density left as an empty box. The near-twin tool’s example simply asserts gravel at 100 lb per cubic foot and gives the reader no way to handle sand, soil, or mulch. Here the density table gives both pounds per cubic foot and pounds per cubic yard for the common loads, with the moisture warning that moves real loads off the table values.
Miss 3: nominal dimensions taken at face value. Brochure math uses the badge size. A bed sold as 7 ft wide that measures 82 inches inside is 2 inches narrower than the badge, and across a 14 ft bed with 2 ft walls that is 4.67 cubic feet, about 467 lb of gravel, quietly missing from every brochure-based estimate. Measure the bed you own; the calculator takes whatever real numbers you give it.
One honest limit remains in the other direction: this tool automates the GVWR payload check, total weight against the rating, and a few hauling guides walk through a fuller worksheet that also splits the load across each axle. This calculator has no per-axle inputs, so the axle-by-axle check is still yours to make with your axle ratings. The payload check itself needs your trailer’s plate and scale figures, which no website can know; that is why the two fields are yours to fill in.
Frequently Asked Questions
Multiply the bed length, width, and wall height in feet to get cubic feet, then divide by 27 for cubic yards. For weight, multiply the cubic feet by the material density in pounds per cubic foot. A 14 by 7 bed with 2 foot walls is 196 cubic feet, or 7.26 cubic yards, and at a gravel density of 100 it carries 19,600 lb of material by volume. Add the GVWR and the empty trailer weight and it also returns the payload and the weight-limited capacity for that material.
It depends on wall height, because the walls are the third dimension. With 2 foot walls the struck capacity is 7.26 cubic yards; with 3 foot walls it is 10.89 cubic yards; with 4 foot walls it is 14.52 cubic yards. All three are level loads; heaping adds more, unevenly.
Up to its payload rating: the GVWR on the data plate minus the trailer’s empty weight, including accessories. A 14,000 lb GVWR trailer that weighs 4,300 lb empty has a 9,700 lb payload, whatever the bed volume says. Enter the GVWR and the empty weight in this calculator and it returns that payload figure, the weight-limited capacity for your material, and a badge naming which limit runs out first.
About 2,700 lb at the standard estimate of 100 lb per cubic foot. Real gravel runs roughly 2,400 to 3,000 lb per cubic yard depending on stone size, type, and moisture, which is why a supplier’s own figure beats any table, including the one on this page.
With light material, yes: a level bed of mulch at 20 lb per cubic foot weighs about 3,920 lb in the worked example’s trailer, well under its payload. With gravel, sand, or soil, no: the same bed of gravel weighs 19,600 lb against a 9,700 lb example payload, so the load has to stop at about half the bed.
Struck capacity is the volume with the load level with the top of the walls, and it is the figure this calculator and most manufacturers quote. Heaped capacity adds a mound above the walls, so it is larger but approximate, because it depends on how steeply the material piles. Payload checks should always use the struck figure.
Because the bed volume is computed in cubic feet, so the density has to be per cubic foot for the multiplication to work. Suppliers often quote pounds per cubic yard instead; divide that figure by 27. Gravel at 2,700 lb per cubic yard is 100 lb per cubic foot.
GVWR, yes, as a total payload check: enter the GVWR from the data plate and the empty trailer weight and it works out the payload, converts it into a weight-limited capacity for your material, and tells you whether volume or weight runs out first. Axle ratings, no: it has no per-axle inputs, so checking the load against each axle rating stays with you.
Nothing changes: the calculator returns the bed volume and, when a density is entered, the load weight, exactly as it did before those fields existed, and no payload lines appear. The payload check only runs when both fields are filled in, because a payload needs both the rating and the empty weight.
Add This Calculator to Your Website
References
- Kaufman Trailers, “Dump Trailer Cubic Yardage” – manufacturer guide to struck cubic yard capacity by bed size, with the note that nominal widths differ from actual inside widths, and per-yard weights for dirt, gravel, and sand. Kaufman Trailers: Dump Trailer Cubic Yardage. Accessed October 2026.
- National Institute of Standards and Technology, Special Publication 811, “Guide for the Use of the International System of Units (SI)” – the conversion reference behind 27 cubic feet per cubic yard and the unit handling on this page. NIST SP 811: Guide for the Use of the SI. Accessed October 2026.
- National Institute of Standards and Technology, “SI Units” – NIST guidance on the units of length and volume used throughout this page. NIST: SI Units, Office of Weights and Measures. Accessed October 2026.
- Code of Federal Regulations, Title 49, Part 393, Subpart I, “Protection Against Shifting and Falling Cargo” – the federal cargo securement rules for commercial hauling, published on the official eCFR. eCFR: 49 CFR Part 393, Subpart I, Cargo Securement. Accessed October 2026.
- Legal Information Institute, Cornell Law School, “49 CFR 393.106, General Requirements for Securing Articles of Cargo” – the specific federal section setting the performance standard a securement system must meet for a hauled load. Cornell LII: 49 CFR 393.106, Securing Cargo. Accessed October 2026.
