Skip to content
CalculatorZilo Logo
  • Home
  • CalculatorsExpand
    • Browse all calculators
    • Education
    • Real Estate
    • Chemistry
  • Finance
  • Math
  • Health & Fitness
  • Science
  • About
  • Contact
CalculatorZilo Logo
Home / Long Tail Pair Calculator
Engineering Calculators

Long Tail Pair Calculator

Published onOctober 4, 2025 Updated onOctober 24, 2026 5:12 pm

A long tail pair calculator models the long-tailed differential pair: two matched transistors sharing one tail resistance, with the output taken from one side. Enter transconductance, collector resistance, and tail resistance for differential gain, common-mode gain, and common-mode rejection ratio (CMRR), then use the Gain With Load tab to see what happens when a real load hangs on the output. The load is part of the predicted gain, so the loaded tab wires it into the formula instead of reporting it for the record only. A separate secondary Measured Gain tab is kept for bench measurements: enter a measured input and output voltage and it reports Vout divided by Vin, with no load input, because a measured output already includes its load.

Long Tail Pair Calculator

Differential gain, CMRR, predicted gain with a load, and secondary measured gain.

Please enter a collector resistance greater than zero.
Please enter a transconductance greater than zero.
Please enter a tail resistance greater than zero.
Please enter a transconductance greater than zero.
Please enter a collector resistance greater than zero.
Please enter a load resistance greater than zero, or leave it blank.

Secondary mode: use this tab only when you have bench measurements. Enter the measured input and output voltages, using the same measurement type for both. There is no load input on this tab, because a measured output voltage already includes whatever load produced it, so no load value can change this result. Never combine this measured gain with the predicted loaded gain: use one or the other.

Please enter an input voltage greater than zero.
Please enter an output voltage greater than zero.
0.00
Result0.00
Second figure0.00
Third figure0.00
Fourth figure0.00

Quick Answer

On the Differential tab, Rc 4,700 ohm, gm 0.04 S, and a 10,000 ohm tail give a differential gain of 94.00 and a CMRR of 400, which is 52.0 dB. On the Gain With Load tab, the same pair driving a 2,200 ohm load gives an effective load of 1,498.55 ohm and a loaded gain of 29.97, which is 29.5 dB: only 31.9% of the unloaded gain survives the load. The Differential and Gain With Load tabs are pre-filled with those cases. The secondary Measured Gain tab is pre-filled with the live bench case: Vin 0.010 V and Vout 0.940 V give a measured gain of 94.00, which is 39.5 dB.

Key takeaways

  • CMRR collapses to gm times Rt in this model. Double the tail resistance and you add about 6 dB of rejection without touching the gain.
  • The load is part of the gain. Effective load is Rc in parallel with RL, and the loaded gain uses that effective load, not Rc alone.
  • A measured output voltage already includes whatever load produced it. Never combine a measured gain with this predicted loaded gain: use one or the other.
  • Measured Gain is a secondary bench mode: Vout divided by Vin, with no load input, so a load value can never change its result.
  • This page covers the electronics circuit only. The retail sales distribution of a similar name lives on its own page, the long tail ratio calculator.
On this page
  • Quick Answer
  • How to use the long tail pair calculator
  • The formulas: differential gain, CMRR, and loaded gain
  • Worked examples that reproduce in the tool
  • Reading CMRR and gain in decibels
  • Why there are two gain tabs: predicted gain versus measured gain
  • What competing calculators miss
  • Limits of this tool: the ideal-pair assumptions
  • Frequently asked questions
  • Add This Calculator to Your Website
  • References

How to use the long tail pair calculator

Choose the tab that matches your question, check the pre-filled example, then press Calculate. The two tabs share one results box, and switching tabs hides the previous result so a differential gain can never be mistaken for a loaded gain. On the Differential tab, enter the collector resistance Rc, the transconductance gm of one transistor, and the shared tail resistance Rt. The model is the classic resistive-tail BJT or FET pair taught in microelectronics courses: matched devices, a single-ended output taken from one collector, and no emitter degeneration. On the Gain With Load tab, enter gm, Rc, and the load resistance RL. Leave RL blank and the tab returns the unloaded gain, which matches the Differential tab exactly for the same gm and Rc. On the Measured Gain tab, enter a measured Vin and Vout, using the same measurement type for both. That tab has no load input: the measured output already includes its load, so the result is Vout divided by Vin and nothing else.

The formulas: differential gain, CMRR, and loaded gain

Differential gain is half of gm times Rc, because the differential signal splits between the two devices while the output is taken from one side: Ad = (gm x Rc) / 2. Common-mode gain is Rc divided by twice the tail resistance, Ac = Rc / (2 x Rt): a common-mode signal sees the tail resistance in both emitter legs. Divide the two and Rc cancels, leaving CMRR = gm x Rt exactly, then CMRR in decibels is 20 x log10 of that ratio. With the pre-filled values: Ad = (0.04 x 4,700) / 2 = 94.00, Ac = 4,700 / 20,000 = 0.2350, CMRR = 400, which is 52.0 dB.

Loaded gain replaces Rc with the effective load. A load resistor on the output sits in parallel with the collector resistor, so Reff = Rc x RL / (Rc + RL), and loaded Ad = (gm x Reff) / 2. With the pre-filled values: Reff = 4,700 x 2,200 / 6,900 = 1,498.55 ohm, and loaded Ad = (0.04 x 1,498.55) / 2 = 29.97, which is 29.5 dB. The parallel combination is the same arithmetic the parallel circuit resistance calculator performs, applied here to the collector node. Decibels use 20, not 10, because these are voltages: the same 20 log10 habit the decibel distance calculator uses for level changes. The voltage, current, and resistance relations behind gm itself follow Ohm’s law, as the ohms to watts calculator sets out.

Measured gain is the bench ratio, not a prediction: Av = Vout / Vin, and Av in decibels is 20 x log10(Av), the same 20 log10 rule used for voltages elsewhere on this page. With the pre-filled bench values: Av = 0.940 / 0.010 = 94.00, which is 39.5 dB. Use the same measurement type, peak with peak or RMS with RMS, for Vin and Vout, or the ratio means nothing. Because the measured Vout was already produced into its load, wiring RL into this ratio would count the load twice: once inside Vout and once as a factor. That is why the Measured Gain tab has no RL input at all, and why its result never changes when a load value changes elsewhere on the page.

Worked examples that reproduce in the tool

TabInputsMain resultAlso shown
DifferentialRc 4,700 ohm, gm 0.04 S, Rt 10,000 ohmAd 94.00Ac 0.2350, CMRR 400 (52.0 dB)
Gain With Loadgm 0.04 S, Rc 4,700 ohm, RL 2,200 ohmLoaded Ad 29.97Reff 1,498.55 ohm, 29.5 dB, 31.9% of unloaded
Gain With Load, no loadgm 0.04 S, Rc 4,700 ohm, RL blankAd 94.00Reff = Rc, 100% of unloaded
Gain With Load, heavy loadgm 0.04 S, Rc 4,700 ohm, RL 4,700 ohmLoaded Ad 47.00Reff 2,350 ohm, 50.0% of unloaded
Measured Gain (Secondary)Vin 0.010 V, Vout 0.940 V, no RL inputMeasured gain 94.0039.5 dB, identical for any load that produced the measurement
Measured Gain (Secondary)Vin 0.020 V, Vout 0.500 V, no RL inputMeasured gain 25.0028.0 dB

The fourth row is the cleanest sanity check on the parallel formula: when RL equals Rc, the effective load is exactly half of Rc, and the loaded gain is exactly half the unloaded gain. The third row is the other boundary: with no load, the effective load is Rc itself and the loaded tab reproduces the differential tab. The measured rows are the live bench parity check: 0.940 divided by 0.010 is 94.00, exactly the live Amplifier Gain result for the same voltages, and the second measured row shows the same division on different voltages.

Reading CMRR and gain in decibels

CMRR tells you how much of an unwanted common signal, such as mains hum picked up equally on both inputs, survives compared with the wanted differential signal. Higher is better, and in this model the cheapest improvement is almost always the tail: raising Rt from 10,000 ohm to 100,000 ohm moves the worked example from 52.0 dB to 72.0 dB without changing the differential gain at all. That is because CMRR equals gm times Rt while differential gain does not involve Rt. The practical limit is that a plain resistor tail large enough for very high CMRR drops too much voltage and starves the pair, which is why serious designs replace the resistor with a current source. This tool models the resistive tail only, so treat its CMRR as a first-pass estimate, not a measured figure.

For loaded gain, the reading to carry away is the retained share. A load equal to Rc costs half the gain. A load much larger than Rc costs little: with RL at 47,000 ohm (ten times Rc), Reff is about 4,272 ohm and the loaded gain is about 85.4, or 90.9% of unloaded. A load much smaller than Rc dominates the parallel pair and the gain collapses toward gm times RL divided by 2. If your loaded gain looks disappointingly low, the load is the first suspect, not gm.

Why there are two gain tabs: predicted gain versus measured gain

An earlier version of this page had a gain tab that divided a measured output voltage by a measured input voltage and reported the load resistance for the record only, with the tooltip and the FAQ both disclosing that the load never entered the math. That disclosure was honest, but the design was a dead input wearing a tooltip. The fix approved for this page wires the load into the gain formula, and the only physically correct place to wire it is predicted gain: effective load Rc in parallel with RL, times gm, divided by 2. That predicted mode is the primary Gain With Load tab. The measured-voltage mode is restored alongside it as a clearly-labelled secondary tab, not removed, because bench measurements are still a legitimate use of this page. The restoration keeps the physics honest by separation, not by combination: the Measured Gain tab has no load input at all, so a load value cannot be wired into a measured ratio and cannot double-count. Wiring a load factor into a measured Vout to Vin ratio would double-count, because a measured output was already produced into its load. So use the predicted tab when you have device parameters, use the measured tab when you have bench voltages, and never combine the two: if you have bench measurements, the measured ratio already includes your load, and it should land near the loaded prediction when gm, Rc, and RL match your circuit.

What competing calculators miss

Differential amplifier tools elsewhere mostly model the four-resistor op-amp circuit, where gain is a resistor ratio such as R2 over R1. That is a different circuit from a long-tailed pair, and it cannot answer the transistor-level question this tool answers: given gm, Rc, and a resistive tail, what CMRR do you get, and what happens to gain when a load hangs on the output? Voltage gain tools aimed at audio add power ratios and output watts, which are useful, but they assume a load model instead of showing the parallel effective load explicitly. None of the rivals in either family prints the loaded-versus-unloaded comparison that tells a designer at a glance whether the load or the device is the problem. This tool does that on every loaded run.

Limits of this tool: the ideal-pair assumptions

The amplifier math is the standard first-pass model, and its simplifications are worth stating plainly. It assumes perfectly matched transistors with identical gm, drops the negative sign that a single-ended output really carries (so gains print as magnitudes), ignores transistor output resistance and emitter degeneration, and treats the tail as a plain resistor rather than the current source used in serious designs, which would push real CMRR far higher than the resistive estimate. Device mismatch, which dominates CMRR in real silicon, is not modelled at all. Treat every figure here as a design estimate to confirm on the bench, not as a measurement.

Frequently asked questions

It models a long-tailed differential transistor pair. The Differential tab computes differential gain, common-mode gain, and CMRR from Rc, gm, and tail resistance. The Gain With Load tab computes the predicted loaded differential gain when a load resistor hangs on the output. A secondary Measured Gain tab computes measured gain from bench voltages, Vout divided by Vin, with no load input.

Ad = (gm x Rc) / 2. The differential signal splits between the two devices while the output is taken from one side, which is where the division by 2 comes from.

Because CMRR is Ad divided by Ac, and Rc appears in both: Ad = (gm x Rc) / 2 and Ac = Rc / (2 x Rt). Dividing cancels Rc and leaves gm x Rt exactly.

Yes, on the Gain With Load tab. That tab replaces Rc with the effective load Rc in parallel with RL, so a heavier load (smaller RL) lowers the predicted gain. On the Measured Gain tab, no: that tab has no load input, and its result never changes with a load value, because a measured output voltage already includes whatever load produced it.

Enter a measured input voltage Vin and a measured output voltage Vout on the Measured Gain tab, using the same measurement type for both, peak with peak or RMS with RMS. The tool reports measured gain as Vout divided by Vin, plus the same gain in decibels as 20 times log10 of the ratio. There is no load input on this tab on purpose: your measured Vout was already produced into its load, so wiring a load factor into the ratio would count the load twice. Use the measured result on its own, or compare it against the Gain With Load prediction, but never combine the two into one figure.

A real single-ended output from one collector of the pair is inverted for one input direction, so a textbook treatment writes Ad with a negative sign. This tool reports magnitudes, which is the convention most CMRR comparisons use, since CMRR takes the absolute ratio anyway. Track signal polarity separately in your schematic.

Yes, with care. Enter your measured Vin and Vout on the Measured Gain tab: that ratio already includes your load. Compare it against the Gain With Load prediction for your gm, Rc, and RL, not against the unloaded figure, or the comparison will look worse than the circuit really is.

Add This Calculator to Your Website

Embed this calculator on your own site with the code below. Copy the code and paste it into your page.

Powered by Calculator Zilo

References

  1. Tai-Haur Kuo, Electronics Lab II, Lab 2 (differential pair gain and CMRR measurement), National Cheng Kung University. Electronics Lab II Lab 2 lecture notes (NCKU). Accessed October 22, 2026.
  2. All About Circuits, Textbook, “Differential Amplifier”. Differential Amplifier (All About Circuits textbook). Accessed October 22, 2026.
  3. Adel S. Sedra, Kenneth C. Smith, Tony Chan Carusone and Vincent Gaudet, Microelectronic Circuits, 8th edition, Oxford University Press. Microelectronic Circuits, 8th edition (Oxford University Press). Accessed October 22, 2026.

Related calculators

Engineering CalculatorsMechanical Advantage CalculatorA mechanical advantage calculator answers three linked questions about one machine cycle: how much does the...Engineering CalculatorsAVI Calculator: Annual Value of Investment ToolEvery investor asks the same four questions in different words: what did I actually earn, what income does this throw off, where is it headed, and when do I break even?Engineering CalculatorsGear Ratio CalculatorEnter the teeth on the driver gear and the driven gear and this calculator returns the gear ratio in decimal...Engineering Calculators3 Phase Current CalculatorSizing a breaker, a motor starter, or a feeder cable for three-phase equipment starts with one number: the line current in amps.Engineering CalculatorsAcceleration Distance CalculatorHow far does it travel while it speeds up?Engineering CalculatorsOhms To Watts CalculatorResistance alone does not tell you the power: the same 24-ohm resistor dissipates 6 watts at 12 volts and 600 watts at 120 volts, because power depends on the voltage or current driving it.

We use cookies to analyze traffic. You can accept or decline cookies below. Learn more

calculatorzilo

CalculatorZilo

Free calculators for everyday life. No signup, no cost, just answers.

Categories

Finance Math Health & Fitness Education Science Real Estate Chemistry Browse all calculators

Popular tools

Mortgage Payment Calculator BMI Walking Calculator Salary Per Minute Calculator Percentage Off Calculator

Company

About Us Contact Us Privacy Policy Terms and Conditions
Disclaimer Cookie Policy DMCA Policy Affiliate Disclosure FAQ Accessibility Statement

© 2026 CalculatorZilo • Free calculators for everyone

  • Home
  • Calculators
    • Browse all calculators
    • Education
    • Real Estate
    • Chemistry
  • Finance
  • Math
  • Health & Fitness
  • Science
  • About
  • Contact
Search