Free Coal Cost Calculator – Estimate Heating Fuel Expenses
Coal looks cheap per ton until you count everything around the ton: delivery, handling, ash and compliance charges, and the share of the heat your appliance never captures. This calculator totals the real delivered cost, converts it to cost per million BTU, the one figure that lets you compare coal honestly against gas, oil, propane, electricity, or wood, and can run that comparison for you.
It accepts quantity in tons, pounds, kilograms, cubic feet, or as a BTU heat load it works backwards from. The pre-filled example, five tons of anthracite for a month, is costed line by line below.
Direct costs
Energy analysis
Coal quality (as entered)
Total coal cost
Tons are US short tons of 2,000 lb. Ash, sulfur, moisture, coal type, and grade are recorded in the summary; the price math runs on quantity, price, heating value, the per-ton charges, and efficiency.
Quick Answer
Key takeaways
- Never compare fuels by the ton, gallon, or therm. Convert everything to cost per MMBTU first; it is the only honest common scale.
- The sticker price was $85 of the $113 all-in cost per ton in the example. Delivery, handling, and fees added a third again.
- Efficiency is a price multiplier in disguise. Dropping from 85 to 70 percent efficiency raises the effective cost per MMBTU by more than a fifth, with no change in the coal price.
- Ash, sulfur, and moisture are recorded in the results for your paperwork, but they do not enter the math. Their real cost belongs in the per-ton fee fields.
How to use the coal cost calculator
Start with the quantity and its unit, the price per ton, and the heating value of your coal as delivered. Add the three per-ton charges your supplier and hauler actually bill: delivery, handling, and any environmental or ash-disposal fee. Set the appliance efficiency to your stove, furnace, or boiler rating, press Calculate, and read the breakdown: purchase cost, each charge, the total, the heat content, and both cost-per-MMBTU figures.
Two modes deserve a note. The quantity unit BTU Required reverses the question: type the heat a job needs and the calculator finds the tonnage that delivers it at your heating value, then prices it. And the calculation type Fuel Comparison Analysis reveals two extra fields, a comparison fuel and its retail price, so coal can be priced against natural gas, heating oil, propane, electricity, or wood on the same per-MMBTU scale. The same BTU-first thinking drives equipment sizing: a heating load in BTU per hour is what the AC tonnage calculator and the AC size calculator use on the cooling side of the building.
How this calculator figures your coal cost
Five short calculations run in sequence, and the results panel shows every intermediate figure.
The comparison mode converts each rival fuel with fixed heat contents: natural gas at 100,000 BTU per therm (so price per therm x 10), heating oil at about 140,000 BTU per gallon, propane at 91,000 BTU per gallon, electricity at 3,412 BTU per kWh, and wood at 20 MMBTU per cord. Those are the standard published heat equivalents used by university extension fuel-comparison tables, and they are approximations by design: your oil grade or cord species will differ slightly.
Worked example, verified in the tool
The pre-filled inputs are 5 tons of anthracite, standard grade, at $85 per ton, 12,500 BTU per pound, with $15 delivery, $5 handling, and an $8 environmental fee per ton, at 85 percent efficiency, for a monthly period.
| Line | Calculation | Result |
|---|---|---|
| Coal purchase cost | 5 tons x $85 | $425.00 |
| Delivery | 5 tons x $15 | $75.00 |
| Handling | 5 tons x $5 | $25.00 |
| Environmental fee | 5 tons x $8 | $40.00 |
| Total direct cost | Sum of the four lines | $565.00 |
| Total heat | 5 x 2,000 x 12,500 BTU | 125,000,000 BTU |
| Effective heat at 85% | 125 MMBTU x 0.85 | 106,250,000 BTU |
| Cost per MMBTU | $565 / 125 MMBTU | $4.52 |
| Cost per effective MMBTU | $565 / 106.25 MMBTU | $5.32 |
Switch the calculation type to Fuel Comparison Analysis, leave the comparison fuel on natural gas at $1.25 per therm, and the same coal prices against gas directly: gas converts to $12.50 per MMBTU, the difference is $7.18 per MMBTU in coal favor, and the reported saving is 57.5 percent, which the tool summary labels Excellent Savings. Treat that verdict as a fuel-only comparison: it excludes the labor of stoking and ash removal that gas never asks of you, which is a real cost even if no invoice itemizes it.
What heating value to type
Heating value does more work in this calculator than any other input, and it is the one people guess worst. According to the U.S. Energy Information Administration, the average heat content of US coal produced in 2025 was about 20.38 million BTU per short ton, roughly 10,200 BTU per pound across all ranks, because so much production is lower-rank western coal. Rank-by-rank figures from standard heating value tables run higher for the coals most home and industrial buyers burn.
| Coal rank | Typical heating value (BTU/lb) | Reading |
|---|---|---|
| Anthracite | About 12,910 | Highest common rank |
| Bituminous | About 10,750 to 14,340 by grade | Wide range: check your analysis |
| Sub-bituminous | About 8,940 to 9,150 | Cheaper per ton, less heat per ton |
| Lignite | About 6,900 | Lowest heat, highest moisture |
A cheap ton of lignite at 6,900 BTU per pound carries little more than half the heat of a ton of anthracite, so a lower price per ton can still be the more expensive heat. If your supplier gives you a coal analysis sheet, use its as-received heating value over any table, including this one. Moisture is the quiet thief: the wetter the coal, the more of each pound is water you paid to haul.
Two honest limits of this tool
The quality fields do not change the price. Ash, sulfur, and moisture percentages, plus the coal type and grade dropdowns, are recorded in the results summary so your printout describes the load, but no formula reads them. That is a deliberate design you should know about, not a hidden flaw: a high-ash coal costs you through disposal, and the honest place for that money is the environmental fee per ton.
The cubic-feet conversion is an estimate. Loose coal weighs roughly 50 to 60 lb per cubic foot depending on size and moisture; the calculator uses 55 lb. Volume-based loads are approximate by nature, so weigh the load if the money matters. The same caution applies to the wood comparison: a cord is a stacked volume, and 20 MMBTU per cord assumes seasoned hardwood.
What competing calculators miss
The best-known rival, the Savvy Calculator coal tool, multiplies price per ton by annual consumption and adds a maintenance line, which answers a budgeting question but not the comparison question. Its own worked example also prints a cost of $0.52 per MBTU for a case whose inputs give $5.20 per MMBTU ($650,000 of annual cost over 125,000 MBTU of heat), a tenfold slip that survives because the page never shows its division. University extension tables, such as the University of Connecticut fuel comparison, get the heat equivalents right but leave you to run every scenario by hand in a spreadsheet.
This calculator differs in three ways. It itemizes the per-ton charges that separate a quote from a bill, so the all-in cost per ton is visible. It reports both the as-delivered and the efficiency-adjusted cost per MMBTU, because appliances, not fuels, are what differ in efficiency. And it carries five ready-made fuel comparisons plus the BTU-required reverse mode, which no rival found for this keyword offers in one tool.
Frequently Asked Questions
It is your total coal cost divided by the heat the coal contains, priced per million BTU. A ton price alone cannot be compared with gas, oil, or electricity prices, because each fuel sells in a different unit. Cost per MMBTU puts every fuel on the same scale.
The first divides your total cost by the heat in the coal as delivered. The second divides by the heat your appliance actually captures after efficiency losses. At 85 percent efficiency, the pre-filled example rises from $4.52 to $5.32 per MMBTU, and the effective figure is the one to compare against other fuels.
Use the figure on your supplier paperwork or coal analysis if you have one. Typical as-delivered values run about 12,500 to 13,000 BTU per pound for anthracite, 11,000 to 13,000 for bituminous, 8,500 to 10,000 for sub-bituminous, and 6,500 to 7,500 for lignite. The pre-filled 12,500 BTU per pound suits the anthracite default.
Not directly. Those three quality figures are recorded in your results summary, but the math runs on quantity, price, heating value, the per-ton fees, and efficiency. Ash affects real costs through disposal, which belongs in the environmental fee or handling cost per ton if your supplier or hauler charges for it.
A short ton of 2,000 pounds, the US convention. The kilogram conversion divides by 907.185, which is one short ton in kilograms. If your invoice prices coal by the metric tonne (1,000 kg), convert the quantity to short tons first: one metric tonne is about 1.102 short tons.
Natural gas priced per therm, heating oil and propane priced per gallon, electricity priced per kilowatt-hour, and wood priced per cord. Pick Fuel Comparison Analysis as the calculation type, choose the fuel, and enter its price in its normal retail unit; the calculator converts it to dollars per MMBTU for the comparison.
It works backwards. Instead of entering a weight, you enter the heat you need in BTU, and the calculator works out how many tons of your coal, at your heating value, deliver that heat, then prices those tons. It suits boiler and kiln jobs that start from a heat load rather than a stockpile.
Add This Calculator to Your Website
References
- U.S. Energy Information Administration, “What is the heat content of U.S. coal?”: 2025 average heat content of US coal produced and consumed, per short ton. EIA: Heat Content of U.S. Coal. Accessed October 2026.
- University of Connecticut, College of Agriculture, Health and Natural Resources, “Comparing Fuel Costs”: heat equivalents and efficiency-adjusted cost per million BTU for coal, oil, gas, propane, wood, and electricity. UConn: Comparing Fuel Costs. Accessed October 2026.
- Manitoba Agriculture, “Heating Fuels Cost Comparison”: worked cost-per-million-BTU method across heating fuels including coal. Manitoba Agriculture: Heating Fuels Cost Comparison. Accessed October 2026.
- The Engineering ToolBox, “Standard Grade Coal: Heat Values”: heating values by coal rank, from anthracite at 12,910 BTU/lb to lignite at 6,900 BTU/lb. Engineering ToolBox: Coal Heat Values. Accessed October 2026.
- Water Professionals, “Fuel and Energy Conversion”: standard BTU contents per unit for coal, gas, oil, propane, wood, and electricity used in fuel cost comparisons. Water Professionals: Fuel and Energy Conversion. Accessed October 2026.
