Hickory Tree Value Calculator
The Hickory Tree Value Calculator prices a standing hickory the way foresters and timber buyers do: it converts trunk diameter (DBH) and merchantable height into board feet with the Ohio State University standing-tree volume tables, then multiplies that volume by a stumpage price per thousand board feet (MBF). No invented rate, no quality multiplier. Enter the tree you measured, pick the log rule your local market trades on, use a published stumpage price or a buyer’s quote, and the result is a number you can trace back to a table and a market report.
Estimated Stumpage Value
Formula Used: Value = (Net Board Feet ÷ 1000) × Stumpage Price per MBF × Trees, with board feet from the Ohio State standing-tree tables (DBH × merchantable height in 16-foot logs)
Quick Answer
An 18 inch DBH hickory with 40 feet of merchantable trunk (2.5 logs) holds 280 board feet on the International 1/4-inch rule, and at a stumpage price of $236 per MBF it is worth $66.08 standing: (280 ÷ 1000) × $236. That is the whole method: measure the trunk, look up the volume, multiply by the going stumpage price. The pre-filled calculator above runs exactly this tree.
Key takeaways
- Value is volume times price: board feet from DBH and merchantable height, times a stumpage price per thousand board feet. There is no other honest shortcut.
- The log rule and the price are a matched pair. International 1/4-inch volumes run higher than Doyle on the same tree, and published prices are quoted on a stated rule basis.
- Grade is priced, not multiplied. A veneer butt log is worth more because buyers pay a higher price per MBF for it, which is why the grade picker on this tool loads a different reference price instead of inflating the volume.
- Stumpage is the standing value, with logging and milling costs already netted out. It will always look small next to retail lumber prices, because it is a different product.
- Quick Answer
- How to use the hickory tree value calculator
- Board feet and stumpage: the formula this calculator uses
- Worked example: an 18 inch hickory with 40 feet of merchantable trunk
- Stumpage prices for hickory: what to enter
- Gross volume, net volume, and the defect deduction
- What competing calculators miss
- Frequently asked questions
- Add This Calculator to Your Website
- References
How to use the hickory tree value calculator
Seven inputs, each one a thing you can measure or look up. Results stay hidden until you click Calculate.
- Diameter at breast height (DBH): measure the trunk 4.5 feet above the ground on the uphill side, as Ohio State University Extension’s Measuring Standing Trees factsheet describes. A tape around the trunk gives circumference; divide by 3.14 for diameter. The same cross-section is what a basal area calculator turns into square feet for stand-level work. The tables cover 12 to 42 inches.
- Merchantable height: the usable trunk only, from a 1-foot stump up to where the trunk tapers to about 10 inches, forks, or runs into heavy branching or defects. Enter it in feet, or switch the units field to logs and enter the count of 16-foot logs directly. Total height is the wrong number here: a 60 foot hickory commonly carries about 40 feet of merchantable trunk.
- Log rule: International 1/4-inch is the default and the rule state agencies and the U.S. Forest Service use. Pick Doyle if your local buyers scale on Doyle, which is common in Ohio, and use a Doyle-basis price with it.
- Log grade: veneer, sawlog, pallet or pulpwood. Changing the grade loads the matching published reference price into the price field. Grade the butt log you can see: straight, clear and sound is high; knots in the first 12 feet, sweep and seams pull it down.
- Stumpage price: dollars per thousand board feet (MBF), pre-filled with the sawlog reference of $236. Overwrite it with your state market report figure or a buyer’s actual quote whenever you have one. The price section below explains where these numbers come from.
- Defect deduction: the share of the trunk that will not saw out: rot, hollow sections, shake, bad sweep. Leave it at 0 for a sound tree. What comes out the other side is net volume, the figure buyers actually pay on.
- Number of trees: for several trees of the same size and grade. Run mixed sizes as separate passes and add them; if the ground itself is part of the question, an acreage calculator helps turn boundary measurements into per-acre figures.
Board feet and stumpage: the formula this calculator uses
A board foot is a volume of wood: 144 cubic inches, pictured as a board 12 inches square and 1 inch thick. A thousand board feet is written MBF, and it is the unit standing timber is priced in.
Nobody can measure the exact board feet inside a standing tree: yield depends on how the tree is bucked into logs, the dimensions sawn, and mill waste. Foresters estimate it with log rules, tables that map DBH and merchantable height, counted in 16-foot logs and half-logs, to a board-foot volume. This calculator interpolates the two standing-tree tables in Ohio State’s factsheet F-35-02 (sourced there from the USDA reference handbook for foresters), so any DBH or height between the printed rows gets a proportional value instead of a nearest-row jump.
Board Feet = Ohio State table value for (DBH, Logs), interpolated between rows
Net Board Feet = Gross Board Feet × (1 − Defect % ÷ 100)
Stumpage Value = (Net Board Feet ÷ 1000) × Price per MBF × Trees
Worked tree: 40 ft ÷ 16 = 2.5 logs; table (18 in, 2.5 logs, International) = 280 bf; (280 ÷ 1000) × $236 = $66.08
The two rules do not agree, and the gap is the point. Ohio State notes that International 1/4-inch is generally considered the best estimate of the lumber that can actually be sawn, while Doyle substantially underestimates smaller trees. On the worked tree, Doyle returns 200 board feet against International’s 280. Neither table is wrong: stumpage prices are adjusted for the rule in use, which is why Penn State publishes prices on the International basis with conversions (a Doyle price runs 1.695 times the International price for the same wood, Scribner 1.159 times). Pick one rule, use its price basis, and name it when you quote the result.
| DBH (inches) | ½ log | 1 log | 1½ logs | 2 logs | 2½ logs | 3 logs |
|---|---|---|---|---|---|---|
| 12 | 30 | 60 | 80 | 100 | 120 | – |
| 16 | 60 | 100 | 150 | 180 | 210 | 250 |
| 18 | 70 | 140 | 190 | 240 | 280 | 320 |
| 20 | 90 | 170 | 240 | 300 | 350 | 400 |
| 24 | 130 | 250 | 350 | 430 | 510 | 590 |
| 30 | 220 | 410 | 550 | 690 | 810 | 930 |
Board feet by the International 1/4-inch rule, from Ohio State University Extension factsheet F-35-02 (USDA NA-FR-15). The calculator’s tables run to 42 inches DBH and 4 logs, and include the Doyle table on the same grid.
DBH and merchantable height
Height ÷ 16 = logs
Board feet in the table
Defect: gross to net
MBF × stumpage price
Worked example: an 18 inch hickory with 40 feet of merchantable trunk
The pre-filled run is the calibration example this page used to be built around, now done directly. An 18 inch DBH hickory, 40 feet of merchantable trunk, International rule, sawlog grade at the $236 reference price, no defect, one tree.
- Convert the height: 40 feet ÷ 16 = 2.5 logs.
- Read the table: at 18 inches DBH and 2.5 logs, the International table gives 280 board feet. The Doyle table gives 200 for the same tree.
- Price it: 280 board feet is 0.280 MBF, and 0.280 × $236 = $66.08.
| Change one thing | Board feet (net) | Value at $236/MBF |
|---|---|---|
| Worked tree: 18 in, 40 ft, International | 280 | $66.08 |
| Same tree on the Doyle rule | 200 | $47.20 |
| Same tree with 10% defect | 252 | $59.47 |
| Five trees of the worked size | 1,400 | $330.40 |
| Bigger tree: 20 in, 40 ft, International | 350 | $82.60 |
| Longer trunk: 24 in, 48 ft (3 logs), International | 590 | $139.24 |
Two lessons in that table. The rule choice alone moves the same tree by $18.88, which is why a quote is meaningless until both sides name their rule. And size compounds quietly: the 24 inch tree carries just over twice the volume of the 18 inch tree, not a third more, because board-foot volume grows faster than diameter.
Stumpage prices for hickory: what to enter
Stumpage is what a buyer pays for the standing tree, before anyone starts a saw. Purdue Extension’s FNR-111 derives it plainly: stumpage value equals delivered product value minus logging, hauling and milling costs. Everything between the stump and the lumber rack comes out of the price, which is why stumpage looks low and why it rises with tree size, log quality and sale volume.
Hickory rarely gets its own line in market reports. It usually sells inside the Miscellaneous Hardwoods group, so the honest reference prices are group averages, and this tool labels them that way instead of inventing a hickory-specific quote. Penn State Extension’s Timber Market Report for the 2017 1st quarter put Miscellaneous Hardwoods at a $236 per MBF average in the Northeast; the 2017 2nd quarter table put the same group at $135, with individual hardwoods in that table running from $78 (hemlock) to $860 (black cherry). The report series is still published, with a second quarter 2026 edition available, and every edition prices stumpage per MBF on the International 1/4-inch basis. Use the newest report for your region when you can; the 2017 anchors pre-filled here exist so the method is visible, not because they are today’s market.
| Grade picked in the tool | Reference price loaded | What the anchor actually is |
|---|---|---|
| Veneer | $860/MBF | Top of Penn State’s 2017 Q2 Northeast hardwood table (black cherry). A ceiling for premium logs, not a hickory quote. |
| Sawlog | $236/MBF | Miscellaneous Hardwoods average, Penn State 2017 Q1, Northeast. The worked-example price. |
| Pallet / cant | $135/MBF | Miscellaneous Hardwoods average, Penn State 2017 Q2, Northeast. Low-grade logs sell at or below the group average. |
| Pulpwood | $78/MBF | Lowest species average in the same 2017 Q2 table (hemlock). Pulpwood often trades by the ton or cord instead. |
Species still matters inside those bands. Shagbark and mockernut are the usual hickory sawlog species, bitternut typically sells lower, and a single clear, straight butt log with veneer potential can out-earn the rest of the tree combined, which is exactly the case where a consulting forester earns their fee. Once logs are actually sawn, the question flips to the lumber end of the chain, where a cost per board foot calculator works out what each board foot cost to produce, and a board calculator counts the board feet in each piece that comes off the saw.
Gross volume, net volume, and the defect deduction
Gross volume is the table number with defects ignored. Net volume is what is left after deducting the parts of the trunk that will not saw out, and net is what gets paid.
Ohio State’s factsheet draws exactly this distinction, and this calculator builds it in as the defect percentage. Rot pockets, a hollow butt, seams, shake and heavy sweep all come out of the same trunk, so they come out of the volume the same way: one honest percentage. A sound, straight hickory usually needs 0 to 5%. Visible rot at the base, a dead top or a badly swept butt log pushes a working estimate toward 10 to 30%. Past that, the tree is cull rather than sawtimber. When you quote the number, state both figures: “280 board feet gross, priced net at a 10% defect allowance” is a sentence a buyer can work with.
This calculator is the right tool for
- Pricing a standing hickory for a timber sale conversation, on a stated rule and price basis.
- Comparing trees in a woodlot on one consistent volume table.
- Checking a buyer’s offer: rerun their trees at their implied price and see if it matches the market reports.
- Estimating what a small harvest is worth before paying for a full cruise.
It is the wrong tool for
- Landscape or shade-tree value for insurance or legal claims, which uses the CTLA trunk formula and can run into five figures for the same tree.
- A veneer-grade butt log, where one log deserves its own buyer inspection and bid.
- Firewood value, which is priced by the cord.
- Retail lumber value: multiplying stumpage volume by a lumber price overstates standing value by an order of magnitude.
What competing calculators miss
The pages ranking for hickory tree value split into generic tree tools that never mention stumpage and hickory pages whose numbers cannot be reproduced. This rebuild was checked against each of them:
- Calculator.city’s Hickory Tree Value Calculator: the closest namesake rival, and it does use the board-foot model, with DBH, merchantable height, log grades and a price per MBF. Run its own worked example before trusting it, though: it credits a 24 inch veneer tree with about 130 board feet, which is Ohio State’s figure for that tree with only a half log of merchantable height. At roughly 3 logs the table gives 590 board feet, so the example understates the tree about four and a half times. Its grade handling also multiplies value by grade on top of a grade-specific price, counting grade twice. This tool’s grade picker changes the price only, never the volume.
- OnlyCalculators’ Tree Value Calculator: two methods share one page: a CTLA landscape appraisal (hickory at a 78% species rating) and a Doyle timber estimate with hickory in a $120 per MBF tier. Both methods are real, but they answer different questions, the $120 tier is a single unsourced figure with no region or date, and a timber seller can easily walk away with the landscape number.
- CtrlCalculator’s Tree Value Calculator: CTLA trunk formula only. Its table values a 24 inch hickory at $12,960, which is a landscape replacement figure, roughly 200 times the stumpage value of a comparable tree, presented with no warning that it is not a timber price.
- The Timberland Investor’s hickory guide: the best hickory-specific teaching in the results: board-foot volume from DBH and log count, defects discussed properly. But there is no calculator to run your own tree, and its headline price of about $4,500 per MBF is a retail lumber price. Multiply stumpage volume by it and a standing tree looks worth ten times its market.
- The gap this page fills: the professional model, with the actual Ohio State tables inside the tool, prices labelled with the report, region and quarter they came from, and arithmetic you can check against the printed table excerpt above.
Frequently asked questions
A board foot is a unit of wood volume: 144 cubic inches, pictured as a board 12 inches wide, 12 inches long and 1 inch thick. Any piece holding 144 cubic inches counts, whatever its shape. Standing timber is estimated in board feet with log rules and priced per thousand board feet, written MBF, so a 280 board foot tree is 0.280 MBF.
DBH is diameter at breast height, the trunk diameter measured 4.5 feet above the ground on the uphill side of the tree. Wrap a tape around the trunk at that height and divide the circumference by 3.14, or use a caliper or a diameter tape that reads diameter directly. If the tree forks below 4.5 feet, measure each stem separately and value the stems individually. This calculator’s tables cover 12 to 42 inches.
Merchantable height is the usable part of the trunk: from a 1-foot stump up to where the trunk tapers to about 10 inches, forks, or hits heavy branching or defects. Total height includes the crown and the thin top, which saw no lumber. Foresters count merchantable height in 16-foot logs and half-logs, rounded to the nearest half-log, so 40 feet of usable trunk is 2.5 logs. A 60 foot hickory often carries only about 40 merchantable feet.
Use the rule your buyer uses, and the price basis that goes with it. Ohio State University Extension calls International 1/4-inch the best estimate of the lumber that can actually be sawn, and state agencies and the U.S. Forest Service use it. Doyle is the common trade rule in Ohio but substantially underestimates smaller trees: on an 18 inch tree with 2.5 logs it returns 200 board feet against International’s 280. Penn State publishes stumpage prices on the International basis and converts Doyle prices at 1.695 times the International price.
Start with your state or regional timber market report. Penn State Extension publishes one quarterly, pricing stumpage per MBF on the International 1/4-inch basis, and hickory usually appears inside the Miscellaneous Hardwoods group rather than under its own name. That group averaged $236 per MBF in the Northeast in the 2017 1st quarter report and $135 in the 2nd quarter. For a live number, ask a consulting forester or take competing bids: local prices move with mill demand and distance to the mill.
Because stumpage buys the standing tree, not the lumber. Purdue Extension derives stumpage as the delivered product value minus logging cost, minus hauling, minus milling, so everything between the stump and the lumber rack comes out of it. Retail hickory lumber at several dollars per board foot also includes drying, grading, storage and retail margin. Multiplying a tree’s board feet by a lumber price overstates its standing value by roughly an order of magnitude.
Yes, through the price. Shagbark and mockernut are the usual sawlog species and bitternut typically sells lower, while any hickory with a clear, straight butt log can draw veneer interest. This calculator has no species dropdown: species reaches the result through the grade you pick and the stumpage price you enter, which is how a forester would handle it too.
No. This is a stumpage estimate for timber conversations, built on published volume tables and a market price you supply. It is not a landscape appraisal: the CTLA trunk formula used for insurance and legal claims can value the same yard tree in five figures, because it prices shade and replacement rather than lumber. For a sale, a boundary dispute or serious money, hire a consulting forester.
Add This Calculator to Your Website
Embed this calculator on your own site with the code below. Pick a size to preview it live, then copy the code.
Powered by Calculator Zilo
References
- Ohio State University Extension, Ohioline. Measuring Standing Trees (Fact Sheet F-35-02). Accessed October 24, 2026.
- Purdue University Extension. FNR-111: Marketing Timber. Accessed October 24, 2026.
- Penn State Extension. Timber Market Report: 2017 1st Quarter. Accessed October 24, 2026.
- Penn State Extension. Timber Market Report: 2017 2nd Quarter. Accessed October 24, 2026.
- Penn State Extension. Pennsylvania Timber Market Report: Second Quarter 2026. Accessed October 24, 2026.
- Michigan State University Extension. How Much Lumber in That Tree? (Extension Bulletin E-2915). Accessed October 24, 2026.
- Oregon State University Extension Service. Measuring Your Trees (EM 9058). Accessed October 24, 2026.
