Skip to content
CalculatorZilo Logo
  • Home
  • CalculatorsExpand
    • Browse all calculators
    • Education
    • Real Estate
    • Chemistry
  • Finance
  • Math
  • Health & Fitness
  • Science
  • About
  • Contact
CalculatorZilo Logo
Home / Demand Charge Calculator
Lighting & Electrical Calculators

Demand Charge Calculator

Published onSeptember 20, 2025 Updated onOctober 21, 2026 5:39 am

For commercial and industrial electricity customers, the demand charge is often the largest single line on the bill, and it has nothing to do with how much energy you used. It is set by your highest 15-minute power draw of the month, multiplied by your utility’s demand rate. This calculator runs it two ways: a Standard mode for a single peak and rate, and a Time-of-use mode that splits on-peak and off-peak demand the way TOU tariffs bill it.

Demand Charge Calculator
Monthly and annual demand charges from peak kW, with a time-of-use split
Demand charge per month
$0.00
Annual demand charge$0.00

Total demand charge per month
$0.00
On-peak charge$0.00
Off-peak charge$0.00
Annual demand charge$0.00

Estimate only. Utilities measure peak demand over 15- or 30-minute intervals; your tariff sheet sets the rate and any ratchet clauses.

Quick Answer

Quick answer: At the pre-filled values, a peak demand of 150 kW at a demand rate of $12.00 per kW produces a demand charge of $1,800.00 per month, or $21,600.00 per year. On the Time-of-use tab, 500 kW on-peak at $7.13 and 150 kW off-peak at $4.94 split into $3,565.00 plus $741.00, a total of $4,306.00 per month and $51,672.00 per year. The energy you used (kWh) does not enter either calculation.

Key takeaways

  • Demand is a speed, not a quantity. The charge prices your fastest 15 minutes of the month, so one bad interval costs the same as running at that level all month.
  • The formula never includes the metering interval as a multiplier. Any tool that multiplies by 15 is wrong by fifteen times; the interval only defines how the peak is measured.
  • Ratchets make peaks sticky. Many tariffs bill at least a percentage of your highest peak from the previous 11 months, so a single spike can raise bills for most of a year.
  • Cutting 10 kW off the worked example's peak saves $120.00 a month at $12 per kW, $1,440.00 a year, every year the lower peak holds.
On this page
  • Quick Answer
  • The demand charge formula, and the two mistakes that wreck it
  • Worked examples: a single peak, and a split time-of-use bill
  • Finding your real peak and your real rate
  • The kVA setting, stated plainly
  • Cutting the peak: what to try, in order
  • What competing calculators miss
  • Frequently Asked Questions
  • Add This Calculator to Your Website
  • References

The demand charge formula, and the two mistakes that wreck it

The formula is one multiplication. Your utility records the highest average power draw over a 15- or 30-minute interval in the billing period and multiplies it by the demand rate on your tariff.

The formulas: Standard: Demand charge = peak demand x demand rate (x billing period factor, if your tariff applies one). Time-of-use: Demand charge = (on-peak demand x on-peak rate) + (off-peak demand x off-peak rate). Annual projection = monthly charge x 12.

The units are where people go wrong. The rate is dollars per kW, a measure of power at an instant, not per kWh, the energy you consume over time. A building can use very little energy and still post a huge demand charge if everything switches on at once, and a building running flat out around the clock can use enormous energy with a modest one. The two charges price different things, which is why this page keeps them separate: your energy side is priced with a cost per kWh calculator, and the two lines only meet on the bill itself.

The second mistake is worse, because some published calculators make it for you. The 15-minute interval is a measuring window, not a factor. A formula written as demand x 15 x rate inflates the charge fifteenfold, and it is circulating on real calculator pages today: 20 kW at $5 per kW is a $100.00 charge, not the $1,500 such a page returns. If a tool's example numbers look suspiciously round and large, check whether the interval has snuck into the multiplication.

Worked examples: a single peak, and a split time-of-use bill

Both modes load with their worked examples, so one click on Calculate in each tab reproduces every figure in this table.

Worked exampleInputsResult
Standard mode150 kW peak, $12.00 per kW, factor 1$1,800.00 per month / $21,600.00 per year
Time-of-use, on-peak500 kW at $7.13 per kW$3,565.00
Time-of-use, off-peak150 kW at $4.94 per kW$741.00
Time-of-use, totalOn-peak plus off-peak$4,306.00 per month / $51,672.00 per year
On-peak: 500 kW
$3,565.00
Off-peak: 150 kW
$741.00

The split is the lesson. The on-peak window carries 83% of this bill even though the off-peak rate is only about a third lower, because the on-peak demand is more than three times the off-peak demand. On a TOU tariff, the cheapest demand is the peak that never happens during the priced window: moving one large load out of that window attacks the $3,565.00 bar, not the $741.00 one. Facilities pricing the energy half of the same shift can pair this with the cost of energy calculator to see both lines move together.

Finding your real peak and your real rate

Your bill already contains both numbers, though utilities label them inconsistently. Look for "billed demand," "maximum demand," or "billing kW" for the peak, and a line priced per kW for the rate.

Three details on the tariff sheet change the answer more than the calculator does. First, the interval: 15 minutes is common, 30 and 60 exist, and a longer interval forgives short spikes. Second, the ratchet. As the Pacific Northwest National Laboratory's Federal Energy Management guidance puts it, a typical demand ratchet bills the larger of this month's peak or about 80% of the highest peak of the previous 11 months, so a 1,000 kW incident sets an 800 kW floor for nearly a year. Third, coincident-peak programs in some regions bill on your demand during the grid's own peak hours rather than yours, which rewards a different kind of shifting. Surveys of utility tariffs commonly put demand charges at 30 to 70 percent of a commercial bill, which is why these clauses are worth reading before any equipment decision.

If your bill shows only energy, ask the utility for interval data. Most commercial meters record it, and a month of 15-minute data tells you exactly which hour set your peak and what was running at the time. Sizing the loads behind that hour is a job for nameplate math, and the amp to watt calculator covers the conversions most nameplates need.

The kVA setting, stated plainly

Some tariffs bill demand on kVA (apparent power) instead of kW (real power), and the Standard mode's unit selector exists for them. Here is the honest part: the selector changes the unit label and the wording of the result, and nothing else. The multiplication is identical, because if your tariff bills kVA, the figure you should enter is your billed kVA, which already includes your power factor.

The conversion, when you need it, is kVA = kW / power factor. A 150 kW peak at a power factor of 0.90 is 166.7 kVA, which at the same $12.00 rate bills $2,000.00 a month instead of $1,800.00. That $200.00 gap is why kVA-billed customers care about power factor correction, and why entering a kW figure into a kVA tariff silently understates the bill by the same ratio. Enter the unit your tariff bills, at the rate your tariff charges for that unit, and the tool's answer is the tariff's answer.

Cutting the peak: what to try, in order

Demand savings come from reshaping when loads run, not from using less energy overall. Work down this list; the early steps are free.

1

Stagger equipment starts. Motors, compressors, ovens and chargers starting together create the coincident spike that sets the month. Sequencing starts ten minutes apart is the single most common fix, and it costs nothing.

2

Shift flexible loads out of the peak window. On TOU tariffs, moving a load from the on-peak window to off-peak cuts the expensive bar in the worked example. Ice making, water heating, charging and batch processes are the usual candidates.

3

Soften motor starts. Soft starters and variable frequency drives remove the inrush surge of large motors and let compressors and pumps ramp instead of slamming on.

4

Correct power factor if you are billed on kVA. Capacitor banks lift a poor power factor toward 0.95, cutting billed kVA for the same real work, as the kVA section above prices out.

5

Add storage or solar sized for the peak, not the day. Batteries discharge through your peak interval and clip it directly. Solar helps only when it generates through that interval, so pair it with the cost per solar panel calculator and your interval data before trusting the demand savings.

Shift the load

Move the work to a cheaper hour instead of storing energy.

  • No capital cost; scheduling and controls only
  • Works when the process has a flexible window
  • Savings limited to loads you can actually move

Shave with storage

Discharge a battery through the peak interval to clip it.

  • Works even when loads cannot move
  • Capital cost, but stacks with TOU energy arbitrage
  • Must be sized to the interval length, not the day

What competing calculators miss

The basic demand formula is hard to get wrong, yet the pages ranking for this term manage it in instructive ways.

Miss 1: the phantom 15. At least one ranking calculator builds the metering interval into its formula, demand x 15 x rate, and its own worked example cheerfully reports a $1,500 charge for inputs that should cost $100. The interval decides which peak gets billed; it never multiplies the price.

Miss 2: no time-of-use mode. Most competing tools accept one peak and one rate. A large share of commercial tariffs bill on-peak and off-peak demand separately, at different rates, and a single-rate tool cannot reproduce those bills at all. The second tab here exists for exactly that tariff shape, with the split shown line by line.

Miss 3: no annual figure, no billing factor. A monthly number hides the budget impact; this tool projects the year alongside every result, and its billing period factor covers the tariffs that scale the standard formula seasonally. Small features, but they are the difference between checking a bill and planning around one.

One honest limit in the other direction: no calculator on this page or any other can apply your ratchet clause, coincident-peak rules, or minimum-demand floors for you, because those live in your tariff's fine print. Treat the result as the charge your peak and rate produce, then check the tariff for the clauses that modify it.

Frequently Asked Questions

A fee based on your maximum power draw (kW) during the billing period, separate from the energy charge for total consumption (kWh). It pays for the grid capacity the utility must keep ready for your peak, even if you only hit that peak once.

Utilities average your power draw over 15- or 30-minute intervals and bill on the highest average. A one-second spike barely registers; several large loads running together through a full interval set the peak.

kW is real power doing work; kVA is apparent power, real plus reactive. They are linked by power factor: kVA = kW / power factor. Some tariffs bill on kVA, which is why this calculator accepts either unit, though you must enter the figure in the unit your tariff bills.

An optional multiplier some tariffs apply for seasonal or time-of-use adjustments. Leave it at 1 unless your tariff sheet names a factor; the calculator then multiplies peak x rate x factor.

Monthly, on each billing cycle. Watch for ratchet clauses: many tariffs bill at least a percentage, commonly around 80%, of your highest peak from the previous 11 months, so one bad month can raise bills for most of a year.

Sometimes. Solar cuts energy charges reliably, but it only cuts demand charges when it is generating through your peak interval. A cloudy afternoon peak erases the benefit, which is why batteries aimed at peak shaving are the dependable demand tool.

Usually not. Most residential tariffs are energy-only. Demand charges are standard for commercial and industrial accounts, and a few utilities now offer optional residential demand or EV rates.

Cut the peak, not the total. Stagger equipment starts so big loads never run together, shift flexible loads out of the peak window, use soft starters or variable frequency drives on large motors, and consider battery storage to shave the interval that sets your month.

Add This Calculator to Your Website

Embed the Demand Charge Calculator on your own site. Pick a size to preview it live, then copy the code.

Powered by Calculator Zilo

References

  1. Pacific Northwest National Laboratory, Federal Energy Management Program (FEDS), "What is a demand ratchet?" - the typical ratchet bills the larger of the current peak or about 80% of the highest peak of the previous 11 months. PNNL FEDS: What Is a Demand Ratchet?. Accessed October 2026.
  2. ComparePower, "Demand Charges Explained for Texas Businesses" - how peak kW from a 15-minute interval is multiplied by the demand rate, with ratchet and load factor explanations. ComparePower: Demand Charges Explained. Accessed October 2026.
  3. Exact Solar, "Commercial Demand Charges: How Solar and Batteries Help" - documents the Department of Energy's ratchet guidance and the separate on-peak, off-peak, distribution and transmission demand charges on commercial tariffs. Exact Solar: Commercial Demand Charges. Accessed October 2026.
  4. GridPoint, "Demand Charges and Margin Compression" - how a ratchet converts one 15-minute event into a near-fixed cost for the following year. GridPoint: Demand Charges and Margin Compression. Accessed October 2026.
  5. OpEx OS, "Demand Charges Explained: Cut Your Electric Bill" - interval measurement, demand ratchets at 75 to 95 percent, and realistic savings ranges from staggering, load shifting and power factor correction. OpEx OS: Demand Charges Explained. Accessed October 2026.

Related calculators

Lighting & Electrical CalculatorsParallel Circuit Resistance CalculatorTwo resistors in parallel are easy.Lighting & Electrical CalculatorsElectrical Cable Size CalculatorThis electrical cable size calculator sizes a cable by voltage drop only.Lighting & Electrical CalculatorsConductor Size CalculatorA conductor has to pass two different tests: carry the current without overheating, and deliver it without losing too much voltage along the run.Lighting & Electrical CalculatorsAmp Watt CalculatorAmps tell you how much current is flowing, watts tell you how much power that flow delivers, and volts are the missing middle term that connects them.Lighting & Electrical Calculators Recessed Lighting CalculatorHow many recessed lights does a room actually need?Lighting & Electrical Calculators Ceiling Light CalculatorMost rooms get their ceiling lights by guesswork: a contractor rule of thumb, a grid copied from the showroom, or however many fixtures were on sale.

We use cookies to analyze traffic. You can accept or decline cookies below. Learn more

calculatorzilo

CalculatorZilo

Free calculators for everyday life. No signup, no cost, just answers.

Categories

Finance Math Health & Fitness Education Science Real Estate Chemistry Browse all calculators

Popular tools

Mortgage Payment Calculator BMI Walking Calculator Salary Per Minute Calculator Percentage Off Calculator

Company

About Us Contact Us Privacy Policy Terms and Conditions
Disclaimer Cookie Policy DMCA Policy Affiliate Disclosure FAQ Accessibility Statement

© 2026 CalculatorZilo • Free calculators for everyone

  • Home
  • Calculators
    • Browse all calculators
    • Education
    • Real Estate
    • Chemistry
  • Finance
  • Math
  • Health & Fitness
  • Science
  • About
  • Contact
Search