Repipe Cost Calculator
Budget a whole-house repipe before you call plumbers. Enter your home size, bathroom and kitchen counts, pipe material and how hard the pipes are to reach, and this calculator builds the estimate the way a quote is built: estimated pipe length, material cost, labor hours, fittings, permit and drywall, then a check of the total against 2026 installed ranges for that material.
Planning estimate only. Real quotes vary by region, foundation type and what the walls hide. Get three written quotes from licensed plumbers before committing. Note that totals print without thousands separators, exactly as the calculator formats them: $7444.38 is seven thousand four hundred forty-four dollars.
Quick Answer
A 2,000 sq ft home with 2 bathrooms and 1 kitchen repipes for an estimated $7444.38 in PEX at moderate access and $100/hour labor: 355 ft of pipe, $177.50 of tubing, $6,922.50 of labor, $44.38 of fittings and a $300 permit, or $3.72 per sq ft, inside the typical 2026 PEX range of $3.50–$7.00. The identical home in copper totals $16,363.75 ($8.18 per sq ft). Change the inputs above to price your own home.
Key takeaways
- Labor is the bill. In the worked example, labor is $6,922.50 of the $7,444.38 total (93%), because the tubing itself is only $0.50 per foot for PEX.
- Material choice roughly doubles or halves the job: the same home is $7,444.38 in PEX and $16,363.75 in copper, driven by both tubing price and a slower install pace.
- Access is a multiplier, not a footnote: difficult access multiplies labor hours by 1.7, easy access by 1.0.
- Every result ends with a range check against 2026 installed ranges, so you can tell whether your inputs describe a routine job or an expensive one.
- Quick Answer
- How to use the repipe cost calculator
- The repipe formula: pipe length first, then four cost lines
- Worked example: a 2,000 sq ft home, step by step
- Where the money goes: labor first, everything else second
- PEX vs copper vs CPVC: picking the new pipe
- What moves the number on a real quote
- Signs the house actually needs a repipe
- What competing calculators miss
- Frequently asked questions
- Add This Calculator to Your Website
- References
How to use the repipe cost calculator
Fill in eight fields and click Calculate. Results stay hidden until you do, and the pre-filled values are the worked example from this page, so the first click reproduces the numbers quoted below.
- Enter the home size, bathrooms and kitchens. Together they set the estimated pipe length: floor area drives the base run, and each wet room adds its own branch pipe.
- Pick the pipe material and the access rating. Material sets tubing price and install pace; access scales the labor hours up or down.
- Enter the labor rate, permit and any separate drywall cost. Use the hourly rate from a real quote if you have one. Permit and drywall are added at face value.
- Click Calculate. You get the total and cost per square foot, the pipe length, the material, labor and fittings lines, the exact formula the tool used, and a range-check verdict for that material.
- Copy or share the breakdown with the buttons in the results box when you want to compare it against a written quote.
Two fields are required: home size and labor rate. Blank bathrooms, kitchens, permit or drywall count as zero. The calculator rejects a home size or labor rate of zero or less, and any negative count or cost, with a plain-language message such as “Home size must be greater than zero.” or “Permit cost cannot be negative.”
The repipe formula: pipe length first, then four cost lines
The estimate starts from pipe length, not from a per-square-foot guess. Length is the ceiling of home size times 0.15, plus 20 ft per bathroom and 15 ft per kitchen, and every cost line is built from that length.
Material = length × tubing price per foot | Fittings and supplies = 25% of material
Labor hours = length × hours per foot × access factor | Labor = hours × hourly rate
Total = material + fittings + labor + permit + drywall | Cost per sq ft = total ÷ sq ft
The constants inside the tool are fixed planning factors, and the results box restates the exact ones used in your run:
| Material | Tubing $/ft | Labor hrs/ft | 2026 range check ($/sq ft installed) |
|---|---|---|---|
| PEX | $0.50 | 0.15 | $3.50–$7.00 |
| Copper | $5.00 | 0.30 | $8.00–$14.00 |
| CPVC | $0.75 | 0.15 | $4.00–$8.50 |
| Galvanized steel | $4.50 | 0.30 | $5.00–$9.00 |
Access factors are 1.0 for easy, 1.3 for moderate and 1.7 for difficult, applied to labor hours only. Two honest limits to keep in mind: the tool counts bathrooms and kitchens, not individual fixtures, so a home with a wet bar and a laundry sink on the far wall will run a little long; and it has no separate stories or foundation input, so the access rating is where a slab foundation or a second floor makes itself felt.
Worked example: a 2,000 sq ft home, step by step
The pre-filled example is a 2,000 sq ft home with 2 bathrooms, 1 kitchen, PEX pipe, moderate access, $100/hour labor, a $300 permit and no separate drywall bill. It totals $7,444.38.
Three more runs of the same calculator, so you can check the tool against this page before you trust it with your own numbers:
| Scenario | Pipe length | Total | Per sq ft | Range check |
|---|---|---|---|---|
| Worked example in copper (same home, same access) | 355 ft | $16,363.75 | $8.18 | Inside the copper range |
| 1,000 sq ft, 1 bath, 1 kitchen, CPVC, easy access, $85/hr, $150 permit, $500 drywall | 185 ft | $3,182.19 | $3.18 | Below the CPVC range |
| 3,500 sq ft, 3 baths, 2 kitchens, galvanized, difficult access, $125/hr, $400 permit, $1,200 drywall | 615 ft | $44,265.63 | $12.65 | Above the galvanized range |
The galvanized row deserves a note: galvanized is in the tool as a priced material so you can see what like-for-like replacement would cost, but it is almost always the pipe being removed, not the pipe being installed. The useful comparisons for a real decision are PEX, copper and CPVC.
Where the money goes: labor first, everything else second
Labor takes 93 cents of every dollar in the worked example. Market guides often say labor is about 70% of a repipe bill; both statements can be true because this tool counts only tubing in the material line, while contractor accounting loads valves, manifolds, demolition and disposal into materials and overhead. Either way, the practical lesson is the same: the hourly rate and the access rating move your total far more than the tubing price does.
That split is why two quotes for the same house can differ by thousands without either plumber padding the bill. A crew that works at 0.15 hours per foot in PEX through an open crawlspace simply logs fewer hours than a crew soldering copper through finished walls, and the labor rate itself varies by region and license level: Bureau of Labor Statistics wage data for plumbers, pipefitters and steamfitters is the sober baseline behind the $45 to $200 per hour spread homeowners actually get quoted, once overhead, insurance and profit are loaded on top of wages.
PEX vs copper vs CPVC: picking the new pipe
PEX is the default choice for most repipes, copper is the premium long-life pick, and CPVC is the budget rigid option. The calculator prices all three on identical inputs, so the comparison is purely about material behavior and install pace.
PEX flexes through walls and around corners with far fewer joints than rigid pipe, shrugs off freezing better than any rigid material, and carries a service life commonly rated at 50 years or more. At $0.50 per foot of tubing and the fast 0.15 hr/ft pace, it produces the lowest totals in the tool, and its $3.50–$7.00 per sq ft range check is where most real quotes land. Copper is the material the Copper Development Association documents for decades of plumbing service: rigid, proven, and preferred in some historic homes and jurisdictions, but tubing at $5.00 per foot and a soldered joint at every turn double the labor pace to 0.30 hr/ft. Expect a 40 to 60 percent premium over PEX on the same house; the worked example’s jump to $16,363.75 is steeper than that because both the tubing price and the hours rise together. CPVC sits between them on price at $0.75 per foot with a PEX-like install pace, though it can turn brittle with age and is falling out of favor with many plumbers. One quirk worth knowing: long pipe runs hold real water volume, and a pipe volume calculator shows how many gallons sit in the lines, which is part of why distant fixtures take time to run hot.
What moves the number on a real quote
Access dominates, region sets the rate, and the drywall line decides whether two quotes are even comparable. Those three factors explain most of the spread between the tool’s low and high scenarios.
- Access and foundation. A ranch on an open crawlspace is the fast case (factor 1.0). Finished walls push the factor to 1.3, and a slab foundation, which forces rerouting through the attic or walls, sits in the difficult 1.7 band. On the worked example, switching moderate to difficult alone adds about $2,100 of labor.
- Regional labor rates. The $100/hour example rate is a middle figure. Lower-cost regions quote well under it and coastal metros well over it, and because labor is over 90% of a PEX total in this model, a $25/hour difference is worth roughly $1,730 on the worked example.
- Drywall and paint. Turnkey repipe specialists bundle opening, patching, texturing and paint; general plumbers often price pipes only. A quote that looks $1,500 cheaper may simply have moved the wall work onto you, which is why the tool gives it a separate line instead of hiding it.
- Project bundling. A repipe scheduled alongside a remodel shares the opened walls and the drywall work. If a bathroom gut is already planned, check the combined budget against bathroom remodel cost per square foot figures and typical renovation costs per square foot before signing either contract.
Signs the house actually needs a repipe
Recurring leaks, rusty water and fading pressure in an older home are the classic triggers. Galvanized and polybutylene systems deserve action before the symptoms force it.
Galvanized steel supply pipe lasts roughly 20 to 50 years and corrodes from the inside: the bore narrows with rust buildup (tuberculation), pressure falls, and the water can run discolored after sitting. A pre-1960 galvanized system is past its rated life even if it has not leaked yet. Polybutylene, installed from 1978 into the mid-1990s, degrades in chlorinated water and fails without much warning; many insurers now flag it or refuse homes that still have it. There is also a regulatory backdrop for the oldest systems: the federal Lead and Copper Rule has pushed water systems to inventory and replace lead service lines, and while that program targets the utility side of the meter, it is one more reason a home’s own aging metal pipe gets scrutinized at sale and at insurance renewal. If the job turns out to be one failed run rather than a whole system, a general plumbing cost calculator prices single jobs better than this whole-house model does.
What competing calculators miss
Repipe estimators split into preset-driven tools and guide pages with no tool at all, and each camp gives something up:
- Preset-heavy estimators (for example CD Calculators’ house repiping calculator): they add foundation type, stories and region selectors, which is genuinely useful, but the extras arrive as fixed presets: drywall at $1,200 to $3,000, a water heater at +$1,500, a main line at +$2,500. If your actual drywall bid is $600, the preset overstates your job and you cannot correct it.
- Quote-builder tools (ServiceAgent, PlumberCalc): built for contractors assembling quotes, with crew, margin and markup fields. Useful for a plumber, opaque for a homeowner who wants to know why the number is what it is: no pipe-length build-up is shown.
- Cost guides with no calculator (Angi, HomeGuide, contractor blogs): solid published ranges (whole-house $1,500 to $15,000, typical around $7,500) but nothing that reacts to your bathroom count, your access or your labor rate.
- The gap this page fills: a transparent build-up you can argue with line by line: estimated feet of pipe, tubing dollars, labor hours at your rate, a 25% fittings allowance, your own permit and drywall figures, and a verdict that checks the result against the material’s 2026 range instead of leaving you with a bare total.
Frequently asked questions
Most whole-house repipes fall between $1,500 and $15,000, with many homeowners paying around $7,500. Per square foot, the ranges built into this calculator are $3.50 to $7.00 for PEX, $8.00 to $14.00 for copper and $4.00 to $8.50 for CPVC. Large homes with difficult access run well past $15,000: the 2,000 sq ft worked example below already totals $16,363.75 in copper, so treat $15,000 as a typical ceiling, not a hard one.
Usually 2 to 5 days for an average home with a professional crew. Larger homes and slab foundations can take up to 10 days. Water is typically shut off only during work hours, and most crews restore service each evening.
PEX suits most homes: it is cheaper, faster to install, resists freezing and lasts 50 years or more. Copper is the premium pick for historic homes and for owners who prefer metal pipe, but the worked example below jumps from $7,444.38 in PEX to $16,363.75 in copper on identical inputs.
This calculator estimates pipe length as the ceiling of home size times 0.15, plus 20 ft per bathroom and 15 ft per kitchen. A 2,000 sq ft home with 2 bathrooms and 1 kitchen works out to 355 ft, and most homes land in the few-hundred-feet range. Sprawling single-story layouts run longer than compact two-story homes of the same size.
Usually yes. Most jurisdictions require a plumbing permit and an inspection for a whole-house repipe, and permit fees commonly run a few hundred dollars. Enter your local fee in the permit field; leaving it blank counts as $0, which understates the total.
Sometimes. Turnkey repipe companies generally include cutting, patching and texturing in their quote, while many general plumbers handle pipes only and leave the walls to you. The calculator keeps drywall repair and paint as its own optional line so the two quote styles stay comparable.
Yes, plan on it. Galvanized steel lasts roughly 20 to 50 years and narrows from the inside as rust builds up, which cuts water pressure and can discolor the water. Any galvanized system installed before 1960 is past its rated life. The calculator prices new galvanized at $4.50 per ft for comparison, but almost nobody repipes with galvanized today.
Replace them. Polybutylene was installed from 1978 into the mid-1990s, degrades in chlorinated water, and is flagged or refused by many insurers. It is not offered as a new material in this calculator because it is no longer installed; budget roughly $3,000 to $8,000 for a typical home, in line with a PEX or CPVC job.
It removes a major buyer objection and can lower insurance premiums by removing burst-pipe risk, and it is a strong selling point in older homes. Treat it as protecting value rather than a dollar-for-dollar value add: buyers expect working plumbing, and they rarely pay a premium for it.
Get at least three written quotes that each name the material, the fixture count, who handles the permit and whether drywall and paint are included. Then run each quote’s inputs through this calculator and compare line by line: pipe length, material, labor hours and the range-check verdict show you exactly where a high quote is high.
Add This Calculator to Your Website
Embed this calculator on your own site with the code below. Pick a size to preview it live, then copy the code.
Powered by Calculator Zilo
References
- U.S. Bureau of Labor Statistics. Occupational Employment and Wage Statistics (OEWS) Tables: Plumbers, Pipefitters, and Steamfitters (47-2152) (national and state wage data behind residential labor rates). Accessed October 24, 2026.
- U.S. Environmental Protection Agency. Lead and Copper Rule (federal drinking-water rule driving lead service line inventories and replacement). Accessed October 24, 2026.
- Copper Development Association. Plumbing Applications (copper tube for water distribution: standards, joining and service performance). Accessed October 24, 2026.
- International Code Council. 2021 International Plumbing Code (IPC) (the model plumbing code most jurisdictions adopt for permitted repipe work and inspections). Accessed October 24, 2026.
- ASTM International. ASTM F876, Standard Specification for Crosslinked Polyethylene (PEX) Tubing (the product standard PEX tubing is manufactured and rated to). Accessed October 24, 2026.
- U.S. Bureau of Labor Statistics. Plumbers, Pipefitters, and Steamfitters: Occupational Outlook Handbook (what licensed plumbers do, licensing and work environment). Accessed October 24, 2026.
- U.S. Environmental Protection Agency. Lead Service Lines (how lead and galvanized service lines are identified and why galvanized lines that absorbed lead are replaced). Accessed October 24, 2026.
