Electric Panel Cost Calculator
What does a new electrical panel cost? Mostly, it depends on amperage and on how much work rides along with the panel itself. Choose your service size, enter your local rates, and this electric panel cost calculator builds an itemized estimate: capacity, installation, extra labor, permit, code-required breakers and extras, then checks the total against the installed price range built in for that amperage.
Quick Answer
At the pre-filled inputs, a 200-amp like-for-like replacement at $8 per amp, with an $800 installation fee and a $200 permit, totals $2,600. The calculator’s built-in sanity check flags that as above its typical $1,300 to $2,000 installed range for 200A, because the capacity line alone ($1,600) plus the full installation fee leaves no room inside that range. Lower the per-amp rate toward $5 and the same job lands inside it.
Key takeaways
- The panel is the small part of the bill. Installation, permits and service work around it decide the total.
- The sanity check is keyed to amperage only. It does not know whether your job is a swap or a full service upgrade, so upgrades with real extras often land above the range legitimately.
- An upgrade is priced by what you enter in Service upgrade extras.
- Every figure here is an estimate for budgeting and quote-checking. The work itself needs a licensed electrician and a permit in most jurisdictions.
- Quick Answer
- How to use the electric panel cost calculator
- How the estimate is built, line by line
- Worked example: the pre-filled 200-amp replacement
- Typical installed ranges by panel size
- Panel swap or service upgrade: the real decision
- Signs the panel needs attention, and how the job runs
- What competing calculators miss
- Frequently asked questions
- Add This Calculator to Your Website
- References
How to use the electric panel cost calculator
Build the job line by line, then click Calculate. The results stay hidden until you do, and every optional line you leave empty is simply left out of the breakdown.
- Panel size: pick the service amperage of the new panel, 100A to 400A. This sets both the capacity cost and the typical range used in the sanity check.
- Cost per amp and installation fee: the two core inputs. The tool’s own guidance puts typical per-amp inputs at $5 to $15 and installation at $500 to $2,000.
- Extra labor: hours beyond the flat fee, at your electrician’s hourly rate, if your quote separates them.
- Permit, breakers and extras: permit and inspection, the count of AFCI/GFCI breakers (priced at $45 each in the tool), a subpanel add-on, and service upgrade extras for meter, conductor and grounding work.
One honest detail about the guidance figures: they are the ranges written into this tool, and they sit comfortably alongside published cost guides. Per Angi’s Charlotte cost data, a 200-amp panel plus installation runs about $1,265 to $1,946, close to the $1,300 to $2,000 range this tool checks against, and panel-only prices there run $243 to $341 for 200A, which is why the hardware is never the story in these estimates.
How the estimate is built, line by line
The total is a straight sum of the lines you fill in. There is no hidden multiplier, no contingency percentage and no regional adjustment inside the tool.
Extra labor = Extra labor hours × Hourly rate
Breaker cost = AFCI/GFCI breaker count × $45
Estimated total = Capacity cost + Installation fee + Extra labor + Permit + Breaker cost + Subpanel + Service upgrade extras
Two conditions shape the breakdown you see. Optional lines only print when they are above zero, so a swap with no extra hours, no breakers counted, no subpanel and no service extras shows just four lines: capacity, installation, permit and total. And any negative cost stops the calculation with an error, because a negative fee is a typo, not a discount. The amperage also decides which sizing questions matter downstream: the service conductors have to match the new rating, which a conductor size calculator works through, and converting the service rating into watts for load planning is a job for an amp to watt calculator.
Worked example: the pre-filled 200-amp replacement
The calculator opens on a 200-amp like-for-like replacement with mid-range rates. Running it unchanged shows both the build-up and how the range check reads it.
| Line | Amount | Share of total |
|---|---|---|
| Panel capacity (200A × $8/A) | $1,600 | 61.5% |
| Installation fee | $800 | 30.8% |
| Permit and inspection | $200 | 7.7% |
| Estimated total | $2,600 | Above the typical $1,300-$2,000 range for 200A |
Now the same rates on a genuine upgrade. Add 4 extra labor hours at $95 and $1,000 of service extras for the meter base, conductors and grounding, and the total is $3,980: capacity $1,600, installation $800, extra labor $380, permit $200, service extras $1,000. Read the sanity check carefully here: the tool still compares that total with the same $1,300 to $2,000 amperage range and reports it as above range. An earlier version of this page described that $3,980 as sitting inside a $2,000 to $4,000 upgrade range; the tool has never contained that range, and its ranges do not change with job type. Above range on a full service upgrade is expected, not a red flag by itself. What the check is really for is catching a mistyped rate on an ordinary job: a $1,050 estimate for a simple 100-amp replacement at $5 per amp, a $500 installation fee and a $50 permit lands inside its $800 to $1,500 range, which is the shape a straightforward swap should have.
Typical installed ranges by panel size
These are the ranges built into the calculator’s sanity check, with the panel-only prices from Angi’s published cost tables beside them for scale. Treat both as budgeting references, not quotes.
| Panel size | Tool’s typical installed range | Panel alone (Angi, Charlotte) | Common reason for this size |
|---|---|---|---|
| 100 amps | $800 – $1,500 | $97 – $195 | Like-for-like replacement in a small all-gas home |
| 150 amps | $1,300 – $1,600 | $146 – $243 | Mid-size home with modest electric loads |
| 200 amps | $1,300 – $2,000 | $243 – $341 | The modern standard: electric HVAC, EV charging, additions |
| 300 amps | $1,800 – $3,500 | $341 – $487 | Large home, workshop or multiple big loads |
| 400 amps | $2,000 – $4,000 | $487+ | Very large homes, often split across two 200A panels |
Regional guides land in the same neighborhood with local variation: Angi’s Chicago figures put a 200-amp installation at $1,350 to $2,075 with an unusually high $600 permit, while Angi’s Washington, DC figures put it at $1,400 to $2,175 with a $65 permit. That permit spread, $65 in one city and $600 in another, is exactly why this calculator takes the permit as an input instead of baking in a national guess. After the upgrade, the running-cost side of the same loads can be sanity-checked with a cost per kWh calculator.
Panel swap or service upgrade: the real decision
The two job types differ in scope, not just price. Most estimate errors come from pricing one while planning the other.
Like-for-like replacement
- Same amperage, new panel and breakers.
- Costs: capacity, installation fee, permit, any AFCI/GFCI breakers.
- Usually one day of work.
- Right call when the panel is old, damaged or a recalled brand, and the service size is still enough.
Service upgrade
- Higher amperage, typically 100A to 200A.
- Adds meter base, heavier service conductors and grounding, priced in Service upgrade extras.
- Can take two days, plus utility coordination.
- Right call when a load calculation says the service is too small, often triggered by an EV charger, heat pump or addition.
Whether an upgrade is needed at all is a load question before it is a cost question. Research from Lawrence Berkeley National Laboratory on avoiding panel upgrades makes the point that existing National Electrical Code options, load calculations on real usage and load management can sometimes serve a new load without a service change, so an electrician’s load calculation comes first and this estimate comes second. Big new cooling loads are a common trigger, and sizing that side of the job is what an AC tonnage calculator is for.
Signs the panel needs attention, and how the job runs
Breakers that trip regularly, lights that dim when a large appliance starts, a panel that is warm to the touch, buzzing or crackling, scorch marks or a burning smell are all stop-and-call-an-electrician signs. So is a fuse box still in service, and so are Federal Pacific Stab-Lok and Zinsco panels, which electricians and inspectors treat as replacement priorities on sight. Planning an EV charger, heat pump, hot tub or addition is the calmer route to the same conversation.
- Load calculation and quote: the electrician confirms the service size the home actually needs and prices the lines in this calculator.
- Permit: filed with the local building department before work starts; this is the $50 to $500 line most budgets forget.
- Utility disconnect and the work day: power is cut, the old panel comes out, the new panel, meter base and conductors go in, circuits are reconnected and labelled.
- Inspection and reconnection: the inspector signs off against the permit, then the utility restores service. Keep the paperwork; insurers and future buyers ask for it.
What competing calculators miss
Panel cost tools split into two camps, and each leaves something out that changes a budget.
- Flat per-amp tools: several ranking calculators multiply amps by a rate, add one fee and stop. No permit line, no breaker count, no subpanel, no service extras, and no check of the answer against any published range.
- Over-built contractor tools: at the other end, some calculators stack contingency percentages and complexity multipliers on top of every line, which inflates a simple swap into an upgrade-sized number. This tool has neither: the total is the sum of the lines you entered, full stop.
- No range feedback: almost none of them tell you whether your total is even plausible for the amperage. The sanity check here, below, inside or above the built-in range, catches the mistyped rate and the forgotten zero before the number hardens into a budget.
- Breakers treated as free: code-required AFCI/GFCI protection is a real per-breaker cost on modern panel work. Here it is a named input at $45 each, not an unpleasant surprise on the invoice.
Frequently asked questions
In this calculator, price it as 200 times your cost per amp, plus the installation fee, permit, any extra labor hours and any extras. At the pre-filled rates (200A at $8 per amp, $800 installation, $200 permit) the total is $2,600, which this tool flags as above its built-in typical range of $1,300 to $2,000 for 200A. A full service upgrade with meter, conductor and grounding extras commonly prices higher than a like-for-like swap: the upgrade scenario worked through on this page totals $3,980.
No. Panel work involves the unfused service entrance, which stays live even with the main breaker off, and it legally requires a licensed electrician and a permit in most jurisdictions. Use this calculator to budget the job and to read a quote intelligently, then hire the work out.
Usually one full day, roughly 6 to 10 hours, for a like-for-like swap at the same amperage. A service upgrade with meter base, conductor and grounding work can take two days, plus time for permits beforehand and the inspection afterwards.
Almost always yes. The permit and inspection line in this calculator defaults to $200, and the guidance built into the tool puts typical permits at $50 to $500. The permit is what triggers the inspection your insurer and a future buyer will ask about, so skipping it is a false saving.
200 amps is the modern standard for homes with electric heating and cooling, an EV charger, a hot tub or an addition planned. A 100-amp service still serves a small all-gas home, but it leaves no headroom, which is why most upgrades in this calculator’s ranges jump straight from 100A to 200A.
A swap replaces the panel at the same amperage: same service conductors, same meter base, mostly the installation fee and permit. An upgrade increases the service size, which adds heavier service conductors, a new meter base and grounding work. In this calculator you price that extra work in the Service upgrade extras field.
The range check compares your total with the built-in installed range for the amperage you picked. Totals land above it when the cost per amp, installation fee or extras are high for the job, or when several extras stack up: extra labor hours, AFCI/GFCI breakers at $45 each, a subpanel and service upgrade extras all add to the same total. The line by line breakdown shows which input is doing it.
This calculator prices them at a flat $45 each, the bulk installed figure written into its code. Enter the count your electrician quotes and the breaker line appears in the breakdown: six breakers add $270. Specialty or smart breakers can cost more in a real quote, so treat the $45 as the tool’s planning figure, not a promise.
Add This Calculator to Your Website
Embed this calculator on your own site with the code below. Pick a size to preview it live, then copy the code.
Powered by Calculator Zilo
References
- Angi. How Much Does It Cost to Upgrade an Electrical Panel in Charlotte, NC? Accessed October 21, 2026.
- Angi. How Much Does It Cost to Upgrade an Electrical Panel in Chicago, IL? Accessed October 21, 2026.
- Angi. How Much Does It Cost to Upgrade an Electrical Panel in Washington, DC? Accessed October 21, 2026.
- Angi. How Much Does Electrical Box Replacement Cost in Houston, TX? Accessed October 21, 2026.
- Lawrence Berkeley National Laboratory (U.S. Department of Energy). Avoiding Panel Upgrades: load calculation and NEC options for electrification. Accessed October 21, 2026.
- Elec2020. Electrical Panel Upgrade Cost in 2026: 100-Amp vs 200-Amp Service. Accessed October 21, 2026.
